PIC-ICD2 Plus debugger and programmer is directly compatible with Microchip’s original MPBA-ICD2 and with it you can do everything you can do with the original MPLAB-ICD2, including PIC Programming. PIC-ICD2 is a low cost, real-time debugger and programmer for all PIC16F, PIC18F and dsPIC DSCs.
Programs can be downloaded and executed in real time and examined in detail with the debug functions of MPLAB. Watches can be set on variables and breakpoints can be set from symbolic labels in C or assembly source code, to allow single steppping through C source lines or into assembly code. 

PIC-ICD2 can also be used as a development programmer for supported PIC MCUs. 

The secret behind In Circuit Debugging is two dedicated hardware lines (microcontroller pins used only during debugging mode) that control In Circuit Serial Programming (ICSP) of the device and, afterwards, debugging through proprietary, on-chip firmware. 

The ICD 2 debug features are built into the microcontroller and activated by programming the debug code into the target processor. There is some shared overhead expense that includes one stack level, some general purpose file registers and a small area of program memory.

The PIC Flex development system has been designed for developer and hobbyist intending to leverage the features available in the 28 and 40 PIN Device families available from Microchip. Use of SMD has allowed us to offer more features and a bigger prototyping area than ever previously provided on any of our boards.PIC Flex includes an optional on board programmer which operates over the serial port and will program all devices in the PIC series of 16F and 18F core so you need no external programmer. It will operate with our standard PC programmer application supplied with the board.The system is compact and is efficiently laid out in a 9 cm x 8 cm PCB; includes onboard PSU, Communications interfaces, and additional footprints for devices extending the system’s flexibility.Tracked power and ground connections enable quick, simple integration and usage. A standard RS232 communications interface is available with DB9 footprint. Standard ICSP interface enables the 16fxxx/18fxxx device to be reprogrammed in circuit with or without the on board programmer. The board is available fully assembled.Features :

•  
  • Optional on board programmer
  • Supports PIC’s in 28 or 40 pin packages.
  • Serial interfaces for standard 3/5 wire serial communications link selectable as DCE or DTE.
  • Full USB circuitry suitable for applications using USB PIC’s with 28 or 40 pin boards e.g. 18F2550, also included link to switch to allow switchable boot into Microchip USB bootloader. (Note this circuitry and PIC is only supplied on the USB versions)
  • LCD Module power connector and contrast trimmer.
  • Optional full on board programmer - connect to the PC and program hex files directly to the on board PIC.
  • All I/O pins available on 0.1” pitch PCB matrix suitable for standard IDC connectors
  • Prototyping area of 280 holes (10×28) on a 0.1” pitch. Large enough for an additional 40 pin DIP device and support circuitry. Including tracked Vcc and Gnd lines.
  • 4 Switches and pull up resistors (with link to allow Switch 4 to drive the PIC reset pin).
  • 4 LED’s with resistors.
  • 2 NPN and 1 PNP general purpose transistors with base resistors for driving relays or higher loads.
  • Links provided to disconnect support circuitry and to allow for low power battery operation.
    Has on board 5V, 1A, regulator and full decoupling.
  • Power LED
  • In Circuit Serial Programmer (ICSP) standard 6 pin connector
  • 20MHz crystal oscillator

Manual

• Download Here.

CostsExcept for the USB variants this board does not include a PIC device.

Click Order Online to go to our online catalogue system for this item, or click here for other ordering options.

Increase efficiency and lower cost using digital power conversion from Microchip. Together with Avnet Memec, Microchip is offering qualified registrants a dsPIC Digital Power Conversion Design Kit. Offer ends May 3, 2010.

 dsPIC DIGITAL POWER CONVERSION DESIGN KIT OFFER 
Together with Avnet Memec, Microchip is offering qualified registrants a dsPIC Digital Power Conversion Design Kit. This kit include a Buck/Boost Converter PICtail™ Plus Daughter Board (AC164133), 16-bit 28-pin Starter Board (DM300027), PICkit™ 3 Debug Express (DV164131) and samples of the dsPIC33FJ16GS502-I/SP. Click the Register link at the bottom of this page to qualify for a kit.

More About Digital Power Conversion
Traditional power conversion products, such as light ballasts, inverters and AC-DC/DC-DC power supplies have employed an analog control loop for basic control of the PWM module, integrated circuits (ICs) and power devices. In these types of power products, additional digital control and communication performed by a microcontroller has been layered on top. In digital power conversion, however, the analog control loop is replaced with a digital control loop, and the PWM module is typically integrated into the same microcontroller that is performing the high-level control and communication.

By using digital loop control to implement power conversion, developers can realize many benefits. These benefits are enabled by the ability to perform power-conversion control via reprogrammable software, as well as the performance and features offered by a digital solution.

Designers using new, flexible DSCs for digital power conversion are experiencing newfound abilities to innovate. For more information on Digital Power Conversion Solutions from Microchip, visit www.microchip.com/SMPS.

Learn how to write your own program, debug it, and use it to start the microcontroller. We have provided plenty of practical examples with necessary connection schematics: temperature sensors, AD and DA converters, LCD and LED displays, relays, communications, and the book is constantly being updated with fresh examples. All code is commented in details to make it easier for beginners. Instruction set, operators, control structures, and other elements of PASCAL are thoroughly explained with many examples. Also, the book includes a useful appendix on mikroPascal for dsPIC development environment: how to install it and how to use it to its full potential.

Authors: Zoran Milivojević, Djordje Šaponjić

Hay all you dsPIC users! There’s a new version of the MPLAB C compiler for dsPICs and PIC24s. Share and enjoy!http://bit.ly/biKpWF

Free passes to the World Meter Design Congress 2010 exhibition floor. Use Promo code MIC001 at http://bit.ly/cviYHx